Optimization and Simulation of CIGS Thin-Film Solar Cells Using Cd-Free Buffer Layers
DOI:
https://doi.org/10.22399/ijcesen.4559Keywords:
CIGS solar cells, SCAPS, 1D simulation, Buffer layer, Cd-free materialsAbstract
In this work, we propose and evaluate four alternative buffer materials Zn₂SnO₄, ZnS, ZrSₓSe₁₋ₓ, and SnS₂ as substitutes for CdS in CIGS thin-film solar cells. The numerical simulations were performed using SCAPS-1D to study the effect of absorber (CIGS) and buffer layer thickness on the overall photovoltaic performance. The CIGS absorber thickness was varied from 1 µm to 3.5 µm, while the buffer thickness ranged between 0.01 µm and 0.06 µm. The results show that increasing the absorber thickness enhances Voc, Jsc, and η, with optimal values obtained for 3.0–3.5 µm. The influence of buffer thickness was relatively small, with the best performance achieved for 0.04–0.05 µm. Among the proposed Cd-free buffer layers, ZrSₓSe₁₋ₓ demonstrated the best performance, achieving results nearly identical to those of the conventional CdS buffer. It exhibited slightly higher Voc and comparable efficiency (η ≈ 22.4%), indicating better band alignment and interface properties.Therefore, ZrSₓSe₁₋ₓ appears to be a strong environmentally friendly alternative to CdS for high-efficiency CIGS solar cells. The optimized device structure Al/ZnO:Al/ZrSₓSe₁₋ₓ/CIGS/Mo achieved a maximum simulated efficiency of approximately 22.4%, confirming its potential for next-generation thin-film photovoltaic applications.
References
[1] A. Romeo, M. Terheggen, D. Abou-Ras, D.L. Bätzner, F.-J. Haug, M. Kälin, D. Rudmann, A.N. Tiwari, Development of thin-film Cu(In,Ga)Se2 and CdTe solar cells, Prog. Photovoltaics Res. Appl. 12 (2004) 93–111. https://doi.org/10.1002/pip.527. DOI: https://doi.org/10.1002/pip.527
[2] H. Heriche, Z. Rouabah, N. Bouarissa, New ultra thin CIGS structure solar cells using SCAPS simulation program, Int. J. Hydrogen Energy. 42 (2017) 9524–9532. https://doi.org/10.1016/j.ijhydene.2017.02.099. DOI: https://doi.org/10.1016/j.ijhydene.2017.02.099
[3] H.S. Wada T, Hashimoto Y, Nishiwaki S, Satoh T, et al. Negami T, High-efficiency CIGS solar cells with modified CIGS surface, Sol Energy Mater Sol Cells. 67 (2001) 10. DOI: https://doi.org/10.1016/S0927-0248(00)00296-8
[4] O. Poncelet, R. Kotipalli, B. Vermang, A. Macleod, L.A. Francis, D. Flandre, Optimisation of rear reflectance in ultra-thin CIGS solar cells towards >20% efficiency, Sol. Energy. 146 (2017) 443–452. https://doi.org/10.1016/j.solener.2017.03.001. DOI: https://doi.org/10.1016/j.solener.2017.03.001
[5] H. Arbouz, A. Aissat, J.P. Vilcot, Simulation and optimization of CdS-n/Cu2ZnSnS4 structure for solar cell applications, Int. J. Hydrogen Energy. (2016) 2–7. https://doi.org/10.1016/j.ijhydene.2016.06.185. DOI: https://doi.org/10.1016/j.ijhydene.2016.06.185
[6] B.L. Williams, V. Zardetto, B. Kniknie, M.A. Verheijen, W.M.M. Kessels, M. Creatore, Solar Energy Materials & Solar Cells The competing roles of i-ZnO in Cu ( In , Ga ) Se 2 solar cells, Sol. Energy Mater. Sol. Cells. 157 (2016) 798–807. https://doi.org/10.1016/j.solmat.2016.07.049. DOI: https://doi.org/10.1016/j.solmat.2016.07.049
[7] A.E. Zaghi, M. Buffière, G. Brammertz, M. Batuk, N. Lenaers, B. Kniknie, J. Hadermann, M. Meuris, J. Poortmans, J. Vleugels, Mechanical synthesis of high purity Cu – In – Se alloy nanopowder as precursor for printed CISe thin film solar cells, Adv. POWDER Technol. (2014). https://doi.org/10.1016/j.apt.2014.03.003. DOI: https://doi.org/10.1016/j.apt.2014.03.003
[8] H.W. Schock, R. Noufi, CIGS-based solar cells for the next millennium, Prog. Photovoltaics Res. Appl. 8 (2000) 151–160. https://doi.org/10.1002/(SICI)1099-159X(200001/02)8:1<151::AID-PIP302>3.0.CO;2-Q. DOI: https://doi.org/10.1002/(SICI)1099-159X(200001/02)8:1<151::AID-PIP302>3.0.CO;2-Q
[9] A. Bernard, Cadmium & its adverse effects on human health., Indian J. Med. Res. 128 (2008) 557–64. http://www.ncbi.nlm.nih.gov/pubmed/19106447.
[10] N. Severino, N. Bednar, N. Adamovic, Buffer layer optimization for high efficiency CIGS solar cells, J. Phys. Conf. Ser. 758 (2016). https://doi.org/10.1088/1742-6596/758/1/012016. DOI: https://doi.org/10.1088/1742-6596/758/1/012016
[11] N.W. Hoy, L.L. Noto, P.S. Mbule, SCAPS-1D simulation of perovskite solar cells with hydroxyapatite scaffold for lead encapsulation and performance optimization, Next Mater. 9 (2025). https://doi.org/10.1016/j.nxmate.2025.101260. DOI: https://doi.org/10.1016/j.nxmate.2025.101260
[12] A. Javed, M.F. Nasir, S. Azam, M.A. Amin, Numerical simulation for a suitable electron transport layer of a lead-free CuInSe2 based perovskite solar cell and PV module, Int. J. Electrochem. Sci. . 20 (2025) 100893. https://doi.org/10.1016/j.ijoes.2024.100893. DOI: https://doi.org/10.1016/j.ijoes.2024.100893
[13] M. Mostefaoui, H. Mazari, S. Khelifi, A. Bouraiou, R. Dabou, Simulation of High Efficiency CIGS solar cells with SCAPS-1D software, Energy Procedia. 74 (2015) 736–744. https://doi.org/10.1016/j.egypro.2015.07.809. DOI: https://doi.org/10.1016/j.egypro.2015.07.809
[14] S. Merdes, F. Ziem, T. Lavrenko, T. Walter, I. Lauermann, M. Klingsporn, S. Schmidt, F. Hergert, R. Schlatmann, Above 16 % ef fi cient sequentially grown Cu ( In , Ga )( Se , S ) 2 - based solar cells with atomic layer deposited Zn ( O , S ) buffers, (2015). https://doi.org/10.1002/pip. DOI: https://doi.org/10.1002/pip.2579
[15] B. Barman, P.K. Kalita, Influence of back surface field layer on enhancing the efficiency of CIGS solar cell, Sol. Energy. 216 (2021) 329–337. https://doi.org/10.1016/j.solener.2021.01.032. DOI: https://doi.org/10.1016/j.solener.2021.01.032
[16] M.A. Ashraf, I. Alam, Numerical simulation of CIGS, CISSe and CZTS-based solar cells with In2S3 as buffer layer and Au as back contact using SCAPS 1D, Eng. Res. Express. 2 (2020). https://doi.org/10.1088/2631-8695/abade6. DOI: https://doi.org/10.1088/2631-8695/abade6
[17] A. Chihi, M.F. Boujmil, B. Bessais, Investigation on the Performance of CIGS/TiO 2 Heterojunction Using SCAPS Software for Highly Efficient Solar Cells, J. Electron. Mater. (2017) 1–8. https://doi.org/10.1007/s11664-017-5547-0. DOI: https://doi.org/10.1007/s11664-017-5547-0
[18] J.M. T, E. K, Numerical Simulation for Optimal Thickness Combination of CdS/ZnS Dual Buffer Layer CuInGaSe2 Solar Cell Using SCAPS 1D, Indian J. Sci. Technol. 12 (2019) 01–06. https://doi.org/10.17485/ijst/2019/v12i45/148395. DOI: https://doi.org/10.17485/ijst/2019/v12i45/148395
[19] M.S. Uddin, R. Hosen, S. Sikder, H. Mamur, M.R.A. Bhuiyan, Photovoltaic performance enhancement of Al/ZnO:Al/i-ZnO/CdS /CIGS/Pt solar cell using SCAPS-1D software, Next Energy. 2 (2024) 100080. https://doi.org/10.1016/j.nxener.2023.100080. DOI: https://doi.org/10.1016/j.nxener.2023.100080
[20] A. Kakade, K.B. Chavan, S. Chaure, N.B. Chaure, The role of window layers on the simulated performance of CIGS solar cell characteristics using SCAPS-1D, Next Res. 2 (2025) 100334. https://doi.org/10.1016/j.nexres.2025.100334. DOI: https://doi.org/10.1016/j.nexres.2025.100334
[21] A. Rabehi et al., “Current–Voltage, Capacitance–Voltage–Temperature, and DLTS Studies of Ni|6H-SiC Schottky Diode,” Semiconductors, vol. 55, no. 4, pp. 446–454, Apr. 2021, doi: 10.1134/S1063782621040138. DOI: https://doi.org/10.1134/S1063782621040138
[22] F. Mekaret et al., “A comparative study of Schottky barrier heights and charge transport mechanisms in 3C, 4H, and 6H silicon carbide polytypes,” AIP Adv, vol. 14, no. 11, Nov. 2024, doi: 10.1063/5.0240123. DOI: https://doi.org/10.1063/5.0240123
[23] A. Bekaddour, A. Rabehi, S. Tizi, B. Zebentout, B. Akkal, and Z. Benamara, “Effect of the contact area on the electrical characteristics of the Ti/6H–SiC (n) Schottky diode,” Micro and Nanostructures, vol. 173, Jan. 2023, doi: 10.1016/j.micrna.2022.207464. DOI: https://doi.org/10.1016/j.micrna.2022.207464
[24] A. Rabehi et al., “Simulation and Experimental Studies of Illumination Effects on the Current Transport of Nitridated GaAs Schottky Diode,” Semiconductors, vol. 52, no. 16, pp. 1998–2006, Dec. 2018, doi: 10.1134/S106378261816025X. DOI: https://doi.org/10.1134/S106378261816025X
[25] A. Ziane et al., “Frequency Dependent Capacitance and Conductance–Voltage Characteristics of Nitride GaAs Schottky Diode,” Semiconductors, vol. 55, no. 1, pp. 51–55, Jan. 2021, doi: 10.1134/S1063782621010206. DOI: https://doi.org/10.1134/S1063782621010206
[26] A. Rabehi, M. Amrani, Z. Benamara, B. Akkal, and A. H. Kacha, “Electrical and photoelectrical characteristics of Au/GaN/GaAs Schottky diode,” Optik (Stuttg), vol. 127, no. 16, pp. 6412–6418, Aug. 2016, doi: 10.1016/j.ijleo.2016.04.113. DOI: https://doi.org/10.1016/j.ijleo.2016.04.113
[27] A. Ziane et al., “Numerical investigation of G-V measurements of metal - A nitride GaAs junction,” Revista Mexicana de Fisica, vol. 70, no. 6, pp. 1–7, Nov. 2024, doi: 10.31349/RevMexFis.70.061604. DOI: https://doi.org/10.31349/RevMexFis.70.061604
[28] A. Douara, A. Rabehi, and O. Baitiche, “Impact of AlN interlayer on the electronic and I-V characteristics of In0.17Al0.83N/GaN HEMTs devices,” Revista Mexicana de Fisica, vol. 69, no. 3, 2023, doi: 10.31349/RevMexFis.69.031602. DOI: https://doi.org/10.31349/RevMexFis.69.031602
[29] A. Douara, A. Rabehi, M. Guermoui, R. Daha, and I. E. Tibermacine, “Impact of AlN Buffer Layer Thickness on Electronic and Electrical Characteristics of In0.17Al0.83N/GaN High-Electron-Mobility Transistor,” Physics of the Solid State, vol. 66, no. 6, pp. 157–164, Jun. 2024, doi: 10.1134/S1063783424600766. DOI: https://doi.org/10.1134/S1063783424600766
[30] A. Rabehi et al., “Optimal Estimation of Schottky Diode Parameters Using Advanced Swarm Intelligence Algorithms,” Semiconductors, vol. 54, no. 11, pp. 1398–1405, Nov. 2020, doi: 10.1134/S1063782620110214. DOI: https://doi.org/10.1134/S1063782620110214
[31] A. Douara, A. Rabehi, M. Guermoui, R. Daha, and I. E. Tibermacine, “Simulation-based optimization of barrier and spacer layers in InAlN/GaN HEMTs for improved 2DEG density,” Micro and Nanostructures, vol. 195, Nov. 2024, doi: 10.1016/j.micrna.2024.207950. DOI: https://doi.org/10.1016/j.micrna.2024.207950
[32] A. Rabehi et al., “Accurate parameter estimation of Au/GaN/GaAs schottky diode model using grey wolf optimization,” Revista Mexicana de Fisica, vol. 70, no. 2, pp. 1–8, 2024, doi: 10.31349/RevMexFis.70.021004. DOI: https://doi.org/10.31349/RevMexFis.70.021004
[33] A. Douara, A. Rabehi, and M. Hamdani, “Effect of Geometrical and Physical parameters of AlGaN/GaN HEMT on the electrical characteristics with AlN spacer layer,” 2022.
[34] A. M. Younsi, M. Elbar, and A. Rabehi, “Structural, Electronic, and Optical Properties of Perovskites CaATe3 (A = Zr Or Hf): A Theoretical Investigation,” Semiconductors, vol. 58, no. 12, pp. 984–992, Dec. 2024, doi: 10.1134/S1063782624601870. DOI: https://doi.org/10.1134/S1063782624601870
[35] A. Rabehi et al., “Modeling the Abnormal Behavior of the 6H-SiC Schottky Diode Using Lambert W Function,” Journal of Nano- and Electronic Physics, vol. 14, no. 6, pp. 06032-1-06032–4, 2022, doi: 10.21272/jnep.14(6).06032. DOI: https://doi.org/10.21272/jnep.14(6).06032
[36] A. Ziane, M. Amrani, Z. Benamara, and A. Rabehi, “Modeling and Simulation of Capacitance–Voltage Characteristics of a Nitride GaAs Schottky Diode,” J Electron Mater, vol. 47, no. 9, pp. 5283–5290, Sep. 2018, doi: 10.1007/s11664-018-6408-1. DOI: https://doi.org/10.1007/s11664-018-6408-1
[37] A. Ziane, M. Amrani, A. Rabehi, and Z. Benamara, “Low- and High-Frequency C–V Characteristics of Au/n-GaN/n-GaAs,” Int J Nanosci, vol. 18, no. 06, p. 1850039, Dec. 2019, doi: 10.1142/S0219581X18500394. DOI: https://doi.org/10.1142/S0219581X18500394
[38] A. Rabehi, H. Helal, D. Zappa, and E. Comini, “Advancements and Prospects of Electronic Nose in Various Applications: A Comprehensive Review,” Jun. 01, 2024, Multidisciplinary Digital Publishing Institute (MDPI). doi: 10.3390/app14114506. DOI: https://doi.org/10.3390/app14114506
[39] A. Douara, A. Rabehi, O. Baitiche, and M. Handami, “Improved electrical characteristics of AlxGa1−xN/GaN High Electron Mobility Transistor by effect of physical and geometrical parameters,” Revista Mexicana de Física, vol. 69, no. 4 Jul-Aug, Jul. 2023, doi: 10.31349/RevMexFis.69.041001. DOI: https://doi.org/10.31349/RevMexFis.69.041001
[40] M. W. Bouabdelli, F. Rogti, M. Maache, and A. Rabehi, “Performance enhancement of CIGS thin-film solar cell,” Optik (Stuttg), vol. 216, Aug. 2020, doi: 10.1016/j.ijleo.2020.164948. DOI: https://doi.org/10.1016/j.ijleo.2020.164948
[41] H. Helal, M. Ahrouch, A. Rabehi, D. Zappa, and E. Comini, “Nanostructured Materials for Enhanced Performance of Solid Oxide Fuel Cells: A Comprehensive Review,” Apr. 01, 2024, Multidisciplinary Digital Publishing Institute (MDPI). doi: 10.3390/cryst14040306. DOI: https://doi.org/10.3390/cryst14040306
[42] H. Helal, Z. Benamara, A. H. Kacha, A. Rabehi, B. Akkal, and M. Amrani, “Electron cyclotron resonance ion source nitridation of Au/n-GaAs schottky diode and current-voltage characterization,” in 2017 5th International Conference on Electrical Engineering - Boumerdes (ICEE-B), IEEE, Oct. 2017, pp. 1–6. doi: 10.1109/ICEE-B.2017.8192119. DOI: https://doi.org/10.1109/ICEE-B.2017.8192119
[43] H. Helal, Z. Benamara, M. Ben Arbia, A. Rabehi, A. C. Chaouche, and H. Maaref, “Electrical behavior of n-GaAs based Schottky diode for different contacts: Temperature dependence of current-voltage,” International Journal of Numerical Modelling: Electronic Networks, Devices and Fields, vol. 34, no. 6, Nov. 2021, doi: 10.1002/jnm.2916. DOI: https://doi.org/10.1002/jnm.2916
[44] A. Rabehi et al., “Optimal estimation of Schottky diode parameters using a novel optimization algorithm: Equilibrium optimizer,” Superlattices Microstruct, vol. 146, p. 106665, Oct. 2020, doi: 10.1016/j.spmi.2020.106665. DOI: https://doi.org/10.1016/j.spmi.2020.106665
[45] H. Helal et al., “A study of current‐voltage and capacitance‐voltage characteristics of Au/n‐GaAs and Au/GaN/n‐GaAs Schottky diodes in wide temperature range,” International Journal of Numerical Modelling: Electronic Networks, Devices and Fields, vol. 33, no. 4, Jul. 2020, doi: 10.1002/jnm.2714. DOI: https://doi.org/10.1002/jnm.2714
[46] F. Bendelala et al., “FDTD Modelling of Nanostructured Hemispherical Plasmonic Light Trapping for Enhanced Ultra-thin GaSb TPV Cell,” Semiconductors, vol. 59, no. 4, pp. 404–411, Apr. 2025, doi: 10.1134/S1063782624603029. DOI: https://doi.org/10.1134/S1063782624603029
[47] H. Helal et al., “Comparative study of ionic bombardment and heat treatment on the electrical behavior of Au/GaN/n-GaAs Schottky diodes,” Superlattices Microstruct, vol. 135, p. 106276, Nov. 2019, doi: 10.1016/j.spmi.2019.106276. DOI: https://doi.org/10.1016/j.spmi.2019.106276
[48] H. Helal et al., “A new model of thermionic emission mechanism for non-ideal Schottky contacts and a method of extracting electrical parameters,” The European Physical Journal Plus, vol. 135, no. 11, p. 895, Nov. 2020, doi: 10.1140/epjp/s13360-020-00916-5. DOI: https://doi.org/10.1140/epjp/s13360-020-00916-5
[49] H. Helal et al., “Conduction mechanisms in au/0.8 nm–gan/n–gaas schottky contacts in a wide temperature range,” Materials, vol. 14, no. 20, Oct. 2021, doi: 10.3390/ma14205909. DOI: https://doi.org/10.3390/ma14205909
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 International Journal of Computational and Experimental Science and Engineering
This work is licensed under a Creative Commons Attribution 4.0 International License.
