Tensile properties and microstructure of AISI 430 ferritic stainless steel welded TIG method
DOI:
https://doi.org/10.22399/ijcesen.699Keywords:
AISI 4130 ferritic stainless steel, tensile properties, TIG method, weldabilityAbstract
In this study, AISI 430 ferritic stainless steel sheets with dimensions of 200x50x2.5 mm were joined by TIG (Tungsten Inert Gas) methods and the tensile properties and microstructure properties of the joined materials were investigated. In microstructural studies, it was determined that a significant grain coarsening occurred in the heat affected zone (HAZ) AISI 430 ferritic stainless steel. Tensile, yield strength and elongation decreased in these steels after TIG welding process.
References
Mustafa, S. and Çam, G., (2023). Investigation into microstructures and properties of AISI 430 ferritic steel butt joints fabricated by GMAW, Int. J. Press. Vessels Pip., 202, 104926, https://doi.org/10.1016/j.ijpvp.2023.104926.
Piia Taxell, P and Huuskonen, P. (2022). Toxicity assessment and health hazard classification of stainless steels, Regul. Toxicol. Pharmacol., 133, 105227, https://doi.org/10.1016/j.yrtph.2022.105227.
Vamshi, M., Singh, S. K., Sateesh, S., Nagaraju, D. S. and Subbiah, R. (2020). A review on influence of carburizing on ferritic stainless steel, Mater. Today: Proc, 26, 937-943 https://doi.org/10.1016/j.matpr.2020.01.151
Sun, M., Liu, S., Cheng, Y., Cheng, Z., Ren, R and Chen, C. (2022). Microstructure characteristics and mechanical properties of the thin-plate AISI 430 ferritic stainless steel joints by interrupted pulsed arc welding, J. Mater. Res. Technol., 21, 4500-4511, https://doi.org/10.1016/j.jmrt.2022.11.063.
Wang, Z., Dirrenberger, J., Lapouge, P and Dubent, S. (2022). Laser treatment of 430 ferritic stainless steel for enhanced mechanical properties. Mater Sci Eng,, 831. https://doi.org/10.1016/ j.msea.2021.142205.
Balram, Y., Vardhan and Ramana, G.V, T. (2021). Study of metallurgical changes and mechanical properties of dissimilar weldments developed by interpulse current TIG welding technique, Proceedings of the Institution of Mechanical Engineers, Part C: J. Mech. Eng. Sci., 235, 1-13, https://doi.org /10.1177/0954406220960780.
Husaini,N Ali., Hamza, J.K and Sofyan, S, E. (2019). Effects of welding on the change of microstructure and mechanical properties of low carbon steel, IOP Conf. Series: Mater. Sci. Eng., 523 (2019) 012065, http:// doi.org/10.1088/1757-899X/523/1/012065
Yan J., Gao, M and Zeng X., (2010). “Study on micro structure and mechanical properties of 304 stainless steel joints by TIG, laser and laser TIG hybrid welding, Opt. Lasers Eng., 48 (4): 512-517.
Kumar, S and Shahi A.S., (2016). Studies on metallurgical and impact toughness behavior of variably sensitized weld metal and heat affected zone of AISI 304L welds, Mater. Des., 89: 399-412, https://doi.org/10.1016/j.matdes.2015.09.145.
Mohandas, T., Reddy, G. M and Naveed, M., (1999).A comparative evaluation of gas tungsten and shielded metal arc welds of a “ferritic” stainless steel, J. Mater. Process. Technol., 94,133-140, https://doi.org/10.1016/S0924-0136(99)00092-8
Ramkumar, K. D., Chandrasekhar, A., Singh, A. K., Ahuja, S., Agarwal, A., Arivazhagan, N.and Rabel, A. M. (2015). Comparative studies on the weldability, microstructure and tensile properties of autogeneous TIG welded AISI 430 ferritic stainless steel with and without flux, J. Manuf. Process., 20, 54–69, https://doi.org/10.1016/j.jmapro.2015.09.008.
Tadepalli, L.D., Gosala, A. M., Kondamuru, L., Bairi, S. C., Lakshmi, A. N and Subbiah, R., (2020). Assessment of Properties on AISI430 Ferritic Stainless Steel by Nitriding process, E3S Web of Conferences 184, ICMED 2020, https://doi.org/10.1051/e3sconf/202018401020.
Pańcikiewicz, K., Świerczyńska, A., Hućko, P and Tumidajewicz, M. (2020). Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels. Materials., 13, 4540. https://doi.org/10.3390/ma13204540
Tong, X.,Zhang, G., Wu, G., Zhang,L., Wang, Y., Jiang, R., Liu, W and Ding, W., (2021) Addressing the abnormal grain coarsening during post-weld heat treatment of TIG repair welded joint of sand-cast Mg-Y-RE-Zr alloy, Mater. Charact., 176, https://doi.org/10.1016/j.matchar.2021.111125.
Pichumani, S., Srinivasan, R and Ramamoorthi, V., (2018). Study the correlation between Microhardness, Microstructure & In-situ thermal analysis of PCATIG weldedments of Al-SiC composite, IOP Conf. Series: Mater. Sci. Eng., 377, 012124 doi:10.1088/1757-899X/377/1/012124
Taşkaya, S., Wu, D., Kurt, M., Liao, Y., Xu, J., & Liao, W. (2024). Exploring the Application of Building Information Modeling (BIM) in Town Planning: Key Roles in the Relationship Between Buildings and Parcels. International Journal of Computational and Experimental Science and Engineering, 10(4);701-717. https://doi.org/10.22399/ijcesen.459
Şen BAYKAL, D., Ghada ALMISNED, Hessa ALKARRANI, & H.O. TEKIN. (2024). Radiation Shielding Characteristics and Transmission Factor values of some Selected Alloys: A Monte Carlo-Based Study. International Journal of Computational and Experimental Science and Engineering, 10(4);549-559. https://doi.org/10.22399/ijcesen.421
Şen Baykal, D., ALMISNED , G., ALKARRANI , H., & TEKIN, H. O. (2024). Exploring gamma-ray and neutron attenuation properties of some high-density alloy samples through MCNP Monte Carlo code . International Journal of Computational and Experimental Science and Engineering, 10(3);470-479https://doi.org/10.22399/ijcesen.422
Çalık, A., & Uçar, N. (2024). Microstructure properties of welded S420MC dual phase steel. International Journal of Computational and Experimental Science and Engineering, 10(2);257-261. https://doi.org/10.22399/ijcesen.336
SOGUT, K. (2023). Shear Behaviour of RC Beams: A Numerical Study. International Journal of Computational and Experimental Science and Engineering, 9(3), 248–252. Retrieved from https://ijcesen.com/index.php/ijcesen/article/view/262
KARACA, C., & OTURAK, H. (2022). Experimental Analysis of Two Different Heating Systems Using Copper Pipe and Carbon Steel Pipe in Shell and Tube Heat Exchanger. International Journal of Computational and Experimental Science and Engineering, 8(3). Retrieved from https://ijcesen.com/index.php/ijcesen/article/view/177
CALIK, A., & UCAR, N. (2023). Microstructure and tensile properties of AISI 410 stainless steel welded TIG method. International Journal of Computational and Experimental Science and Engineering, 9(4), 394–397. Retrieved from https://ijcesen.com/index.php/ijcesen/article/view/284
RWASHDI, Q. A. A. D., WAHEED, F., GUNOGLU, K., & AKKURT, İskender. (2022). Experimental Testing of the Radiation Shielding
Properties for Steel. International Journal of Computational and Experimental Science and Engineering, 8(3), 74–76. Retrieved from https://ijcesen.com/index.php/ijcesen/article/view/179
SYLA, N., ALİAJ, F., ELEZAJ, N., & DALİPİ, B. (2021). Comparison of Experimental Curves of Alloy Steels after Gas Nitriding. International Journal of Computational and Experimental Science and Engineering, 7(2), 46–49. Retrieved from https://ijcesen.com/index.php/ijcesen/article/view/147
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 International Journal of Computational and Experimental Science and Engineering
This work is licensed under a Creative Commons Attribution 4.0 International License.
